Troubleshooting: Stains, Chalk & Mildew

DESCRIPTION

The formation of fine, white powder on the surface of the paint film due to weathering, which may give the appearance of color fading. Although some degree of chalking is normal and can be a desirable way for a paint film to wear, excessive paint film erosion may result in heavy chalking.


POSSIBLE CAUSES
  • Oil-based paints tend to chalk more than latex paints.
  • Use of a low-grade, highly pigmented paint.
  • Factory-finished siding can develop an excessively thick chalk layer and may require power washing to ensure complete chalk removal.
  • Use of interior paint for an outdoor application.
  • Not adequately sealing a porous surface.
  • Over-thinning paint.
  • Spreading the paint too thinly.

SOLUTION

Remove chalk by washing or power washing the surface with an appropriate cleaner. If some chalk remains after first washing, then wash again for complete removal; scrubbing may be necessary. Rinse well with clear water. Allow to dry thoroughly.

Brick areas that are stained by "chalk run-down" should be scrubbed with a stiff brush and detergent. Professional cleaning may be required to remove this staining.

For the best resistance to chalking, use higher-quality acrylic coatings.

DESCRIPTION

Accumulation of dirt, dust particles, and/or other debris on the paint film.


POSSIBLE CAUSES
  • Exterior: soil splashing onto siding, air pollution, and car exhaust.
  • Interior: air-borne dust and household dirt.

SOLUTION

Wash the surface; if it comes clean, painting may not be necessary.

Interior - Remove stains, dirt and marks, using a soft cloth or sponge with water or a general-purpose household cleaner. Penetrating stains and marks may be removed either by carefully using an abrasive cleaner and water or by applying a solution of household bleach diluted with water and then rinsing with clean water.

Exterior - Remove dirt with a scrub brush and detergent solution or pressure washing, followed by a thorough rinsing. While dirt accumulation cannot be eliminated entirely, satin, gloss, and high-gloss paints are more resistant to picking up dirt than flat paints due to their smoother finish.

DESCRIPTION

Crusty, white salt deposits, which are leached to the surface of mortar or masonry as water passes through it. Efflorescence is often seen as a white fluffy deposit of salt crystals on cementitious (e.g. masonry) wall surfaces. Efflorescence depends on the presence of salt and moisture, and the growth of crystals will continue as long as both are present. The salts are present in the mortar, blocks, or concrete structure, and the moisture is usually attributable to some building defect. When emanating from mortar in brick or block buildings, efflorescence will appear as narrow bands corresponding to mortar joints.


POSSIBLE CAUSES
  • Failure to adequately prepare surface by removing all previous efflorescence.
  • Interior moisture escaping through exterior masonry walls.
  • Exterior moisture driven through masonry walls by wind and rain.
  • Basement walls that are not properly sealed against ground moisture penetration.
  • Insufficient curing time for new cement or mortar.

SOLUTION

If excess moisture is the cause, eliminate the source by repairing the roof, cleaning out gutters and downspouts, and sealing any cracks in the masonry with a quality caulk or sealant.

If moisture is originating inside the building, consider installing vents or exhaust fans, especially in kitchens, bathrooms, and laundry areas.

If moisture is being driven through the walls from the outside, apply a waterproofing coating to the outside.

Remove the efflorescence and all other loose material with a wire brush, power brush, or low-pressure washing, and then thoroughly rinse the surface.

If the surface is highly alkaline, wash with a mild solution of a Phosphoric Acid or Muriatic Acid.

Painting should be delayed if efflorescence continues.

DESCRIPTION

Black, gray, green, or brown spots on any surface. Mildew is a live growth that feeds on moisture and organic matter and is spread by mildew spores. Paint does not cause mildew.


POSSIBLE CAUSES
  • Mildew forms on interior and exterior surfaces that tend to be damp or receive little or no direct sunlight.
  • Painting over a surface containing mildew.

SOLUTION

Test for mildew by applying a few drops of household bleach to the area, if it is bleached away, the discoloration is probably mildew; if it does not disappear, it is probably dirt.

Before painting, remove mildew by washing the surface with a solution of 1 part liquid bleach and 3 parts water. Do not add detergents or ammonia to the bleach/water solution. Wear protective eyewear, protective clothing, and waterproof gloves. Apply the solution and scrub the mildewed area. Quickly wash off any of the mixture that comes in contact with your skin. Allow the solution to remain on the surface for 10 minutes. Rinse thoroughly with water and allow the surface to dry before painting.

To protect against mildew, use a top-quality paint, and clean when necessary. Install an exhaust fan in high-moisture areas. For exterior surfaces, keep shrubs and other plants pruned to allow for air circulation and light penetration.

Use a product that contains agents that inhibit the growth of mildew on the surface of paint film.

If mildew is the only problem, painting may not be necessary after cleaning the surface.

DESCRIPTION

Black, brown or tan discoloration on the paint surface due to migration of tannins from a wood surface through the paint film.


POSSIBLE CAUSES
  • Typically occurs on "staining woods" such as redwood, cedar, and mahogany, or over knots in certain other wood species, though tannin staining may occur with any kind of wood. Most tannins are water-soluble, some are solvent-soluble. Application of latex coatings directly to these woods may develop a stain on the finish coat if the product is not specifically designed to trap these tannins.
  • If the dry paint film is intact and discoloration occurs at a later date, then staining is being caused by water within the surface. The moisture will migrate and eventually carry staining substances from within the wood to the surface of the paint film.

SOLUTION

If dry paint film is intact and discoloration is occurring at a later date, then internal moisture is usually the cause. The moisture source must be located and corrected. Allow the surface to dry thoroughly. Check to be sure the water has not affected the adhesion of the primer and paint.

Seal stains with an alkyd/oil primer or a coating designed to trap these tannins.

Note: Even with proper preparation and recommended products, tannin bleed can still occur, especially on new wood, with either latex or oil topcoats.

To wash off the tannin stain, use 10% Oxalic Acid and 90% Water or a comparable product that contains a similar solution.

DESCRIPTION

Stains in the paint surface caused by virtually anything that would bleed, leak, or stick to the paint film.


POSSIBLE CAUSES
  • Water stains.
  • Tobacco smoke leaves yellow stains.
  • Smoke and soot damage from a house fire or wood burning stove or fireplace.
  • Grease and oil.
  • Rust.

SOLUTION

Water stains: The source of the water must be found and corrected. Excessively damaged wood, plaster, or drywall may need to be replaced. Peeling paint must be removed if present. The stained area must be properly sealed with a stain blocking primer.

Tobacco smoke stains, smoke and soot, and grease and oil all should be cleaned as much as possible from the surface using a solvent-based degreaser or other appropriate cleaner. Seal stains with a stain blocking primer before topcoating.

Rust must be mechanically removed (with a brush or power tool) and the surface primed with a rust-inhibiting primer.

Tannins are compounds that occur naturally in wood that can be leached out, generally with water, and discolor a coating. (See Tannin Staining for more).

Solvent-soluble stains (oil, grease, tar, solvent-based markers, etc., and minor dried water stains) may be removed with a solvent-based cleaning solution.

Water-soluble stains (dried water stains, smoke stains and related odors, grease, ink, and pencil stains) may be removed with a water-based cleaning solution.